sadsad x
Hover over the picture to zoom

Adafruit DotStar Digital LED Strip - Black 144 LED/m - One Meter

Product Code: MP01717
Supplier Code: 2241
(0 Comment)
2,008.88 TL + VAT
Price Including VAT
2,410.66 TL
Stock Quantity : 2
Bu Ürüne Özel Kampanyalar
  • Features
  • Payment Options
  • Comments (0)
  • Description

    Move over NeoPixels, there's a new LED strip in town! These fancy new DotStar LED strips are a great upgrade for people who have loved and used NeoPixel strips for a few years but want something even better. DotStar LEDs use generic 2-wire SPI, so you can push data much faster than with the NeoPixel 800 KHz protocol and there's no specific timing required. They also have much higher PWM refresh rates, so  you can do Persistence-of-Vision (POV) and have less flickering, particularly at low brightness levels.

    Like NeoPixels, DotStar LEDs are 5050-sized LEDs with an embedded microcontroller inside the LED. You can set the color/brightness of each LED to 24-bit color (8 bits each red green and blue). Each LED acts like a shift register, reading incoming color data on the input pins, and then shifting the previous color data out on the output pin. By sending a long string of data, you can control an infinite number of LEDs, just tack on more or cut off unwanted LEDs at the end. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you.

    However, unlike NeoPixels, these LEDs have 2 wires (input and output) for sending data - one clock pin and one data pin. That means you need two pins, not one, to control DotStars. Because the clock and data is seperated, you can use any processor speed or type to control these strips, and you don't have to worry about being careful with the timing. Hardware SPI support is handy but not required. This makes them excellent for use with any microcontroller or microprocessor, including Arduino, Raspberry Pi, BeagleBone, Propeller, SparkCore, and any 'raw' microcontrollers/microprocessors. It's very easy to port the library, and you can send data to the pixels at up to 32MHz clock rate!

    Another nice thing about DotStars is their high PWM rate. You only have to set the 24-bit color data for each pixel LED once, and then the LED+built-in-chip will handle the PWMing of the red, green and blue. On NeoPixels, this PWM rate happens 400 Hz, which works well but is noticably at lower brightnesses and if the strip is moving in any way.  DotStars have a 20 KHz PWM rate, so even when moving the strip around, you won't see the pixelation, the color blending is very smooth.

    Technical Details

    •  * Width (with weatherstripping): 14mm / 0.55"
    •  * Width (w/o weatherstripping): 12.7mm / 0.5"
    •  * Thickness (with weatherstripping):  4mm / 0.16"
    •  * 144 LEDs per meter
    •  * Pixel pitch: 7mm / .275" between LEDs
    •  * Operating temperature: -40°C - 40°C
    •  * Storage temperature: -10°C - 50°C

    Technical specs (for the LEDs):

    •  * SK9822 Datasheet
    •  * LED Brightness: Red ~600mcd, Green ~500mcd, Blue ~150mcd
    •  * Beam angle: ~160°
    •  * Max current draw per RGB LED: ~60mA (20mA max per Red, Green & Blue LED)
    •  * Note: Strips come with 4 solder points per segment, but the arrangement may vary depending on the supplier, so please check when soldering/powering!
Prepared by  T-Soft E-Commerce.